Name: HappyModel CrazyF411 F4 2-4S Whoop/Toothpick AIO Flight Controller w/ 20A 8Bit 4in1 ESC - ELRS 2.4GHz (UART)
Brand: Happymodel
SKU: sku-40207940485233
Price: 85.13 CAD
Availability: InStock

Minimum quantity	Discount
Buy 2 +	Get 10% discount

Buy 2 +, Get 10% discount

HappyModel CrazyF411 F4 2-4S Whoop/Toothpick AIO Flight Controller w/ 20A 8Bit 4in1 ESC - ELRS 2.4GHz (UART) at WREKD Co.

SAVE 5% OFF YOUR FIRST ORDER
Use discount code FIRSTLEGENDS at checkout.

EXCLUSIVE DISCOUNTS AVAILABLE
Military, First Responders & Students
Learn More

Price

In Stock

Ask us a question

Quantity

NOTE: This item is on backorder, which means it will be delivered as soon as we receive our next shipment from our supplier. This typically ranges from 1 to 3 weeks.

Ships from: Florida Warehouse

Learn about our Shipping and Return Policy

Earn 340 CaveCoin by purchasing this item.

Log In or Sign Up to start earning on your next order.

About this item

Equip your 2-4S drone with the HappyModel CrazyF411 F4 Flight Controller. Enjoy flying with its 20A 8Bit 4in1 ESC and ELRS 2.4GHz receiver featuring a high-sensitivity SX1280 frequency chip for low latency, high packet rate, and great range. With a big Mosfet that supports up to 20A currents, this controller is perfect for FPV drones and strong enough for race or freestyle flying. This flight controller lets you update firmware through Betaflight pass-through or WIFI. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. The default firmware is ELRS V3.0.1. Get ready to take your drone game to the next level!

Browse the rest of our Whoop AIO Boards and our Happymodel gear.

Features

Integrated serial 2.4GHz ExpressLRS receiver
Pre-installed with Bluejay firmware)
Coming with a BMI270 gyro

Specifications

Flight Controller

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: ICM42688P
Mount pattern: 25.5x25.5 M2
Size: 32x28x9mm
Power supply: 2-4S Lipo battery
Built-in 20A Blheli_S ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1.5A BEC
Flight controller firmware target: CRAZYBEEF4DX
Weight: 4.97

Onboard 4in1 ESC

MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.18.1Firmware target: F_H_40_48_v0.18.1
Default protocol: DSHOT150/DSHOT300/DSHOT600

Onboard UART ExpressLRS 2.4GHz Receiver

Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1

Onboard voltage and Amperage Meter Settings

Voltage meter scale setting 110
Amperage meter scale setting 470

Includes

1x HappyModel CrazyF411 F4 2-4S Whoop/Toothpick AIO Flight Controller w/ 20A 8Bit 4in1 ESC - ELRS 2.4GHz (UART)
2x Wire
1x Hardware Set
4x Grommets

Wiring Diagram & Binding Procedure

Binding procedure

Supply power to the flight controller by plug USB, wait until the green LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the green LED light will start to double-flash, which means that the RX enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The green LED should blinking slowly first then turn to solid, that means binding was successfully. If the green led still keep double flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”

Receiver LED status meanings

Green LED solid means bind successful or RC link established; Green LED double-flash means get into bind mode; Green LED flash slowly means no RC signal input from TX module; Green LED continuous flash fast means ExpressLRS wifi enabled.

Bind successful